How To Measure Chain Size For Windlass

P = pitch inside link. This plate is located on the gear case of your windlass and tells you the model and serial numbers of the windlass.

Today, there is a wide assortment of Cranes available, out

6 or 7mm chain to 12mm rope;

How to measure chain size for windlass. Thats important, because it is gravity that stows the chain, and that requires at least 15in of fall between the capstan and the top of the heaped chain. For anchor chain the calibration is very important. If the links are the correct diameter but the length wrong, the gypsy may not catch the links to get traction.

This is the diameter of the wire used to manufacture the link of chain. This number will likely be to the right of either the brand name or the drive link number. The 8mm chain will cost more than 6mm.

This number should be less than the maximum pull of the windlass you have selected. The boats specification sheet and sometimes the owners manual will have your boat length listed. If you know the chain size and manufacturer, then simply go to the maxwell web site, look up your chain, scroll down to your windlass and a dot in the matrix will indicate and guide you to the chainwheel to be used with your specific windlass and chain.

Two possible gypsies (opt.1/2) are possible. Chain and the size of the rope match the specifications for the windlass gypsy. Short link is the preferred type of chain of marine gypsies and windlasses.

Two possible gypsies (opt.1/2) are possible. Marking as a backup is still a good idea. If you do not know the chain size and manufacturer, then use the illustrated chain diagram (below) and indicated dimensions information to measure your chain.

This measurement refers to the gauge of the chainsaw. Also, the rope must be spliced to the chain. Another issue is matching the gypsy on the windlass to the chain size and type.

A windlass gypsy designed for 5/16 high test chain will not work on 5/16 bbb, which has shorter, more compact links. First, determine the total weight of the anchor and rode. For example, if your chainsaw read .050/1.3, this means that the chains gauge.

The chain rod diameter is only one critical number, but the length of chain may vary based on the purpose of the chain. You multiply the total weight of your anchor and chain x4 (x2 for v6 to v12). If your yacht has coped with 6mm chain for years (and if the chain is rusty and the windlass old) there was never a need for 8mm.

If ground tackle is too heavy or close to the windlasss maximum pulling power, or if the boat has lots of windage and/or displacement, select the next larger size of windlass. If your windlass is vertical the gear box and motor are below deck. This then becomes the size of the chain for example 8mm, 10mm etc.

To identify your ideal windlass first look for our nameplate. Likewise, how do you measure a windlass chain? Why not keep the 6mm chain and invest in some decent snubbers and maybe a better anchor.

The most useful way to rate windlass performance is by looking at what it will lift and at what speed. If it is horizontal your unit is all above deck. A consistent pitch throughout the length of chain enables the chains to run smoothly on the gypsy.

Measure one foot of the chain with a tape, then count the links. The most popular gypsy is for 1/4ht and 1/2 rope. This describes the type of chain.

Chain counters are mechnical devices which count the links in your chain as they pass the windlass. Identify the number printed in both millimeters and inches. It is best to measure a few links just in case you grab a bum one, unlikely but possible.

The size of your anchor locker and available fall. However, if youre unsure of your boat length, measure the hull, from the tip of the bow to the center of the stern. 8 or 9mm chain to 14mm.

By the way, the size of the chain in regards to the diameter of the metal is not the important factor. The weight of your anchor. All calibrated chain supplied by william hackett has a batch number marked approximately every 20th link, this ensures that we can maintain our traceability once the chain has been put into service.

Measure the depth of the anchor locker to determine the amount of fall available (distance between the top of the anchor locker and the top of the anchor rode when it is. Anchor chain is measured by the thickness of the steel making up the links. Often availability and the cost of the right gypsy enter the calculus of which chain size and type is right.

They don't mark the chain, but they can provide a reliable measurement of how much chain is out. Determine the length of your boat. Your windlass gypsy is specifically engineered to catch links of a certain dimension.

Having selected the vertical or horizontal windlass sized for your boat length and displacement, the correct windlass pulling power for your needs must be determined using the following formula: Measure away from the weld, the weld zone can be both bigger and smaller than the wire size depending on exactly what machinery it was made on. What matters most in the windlass for correct fit in the gypsy is the number of links per foot in the chain.

It cannot be joined to the chain with a shackle or any other mechanical coupling device. How to measure an anchor chain anchor chain is measured by the thickness of the steel making up the links. Select a few at random and not next to each other.

Rope size on an auto rope to chain winch is dictated pretty much by the chain size. Calibration size/diameter pitch 10 links; Take a section of your chain, lay it out in a straight line, and measure the dimensions as shown below.

Please complete the table below the drawings with the dimensions and other information requested, and forward to maxwell marine limited. Many windlasses have a selection of gypsies, which can be special ordered to fit the rode on your boat. If you know what size chain the rope is easy.

Instructions for sizing an anchor chain. Calibrated chain measurement range for each calibration; All 8mm or 10mm tells you is the diameter of the wire used to bend and weld into links.

Requirements can vary, even for the same model of windlass, so always confirm the listed dimensions with your windlass manual.

Pin by sunny crane machine on electric hoist / winch